cements, metal to glass, stone



cements, metal to glass, stone defined in 1909 year

cements, metal to glass, stone - Cements, Metal to Glass, Stone;
cements, metal to glass, stone - For attaching metal plates, such as letters, etc., to flat sheets of glass, the following may be used:
  1. Copal varnish, 15; drying-oil, 5; turpentine, 3. Melt in a water-bath and add 10 parts slaked lime.
  2. Copal varnish, 15 parts; boiled linseed-oil, 5; Venice turpentine, 5; glue, melted in the smallest possible quantity of water, 5 parts. Melt together and add 10 parts of powdered quicklime.
  3. Carpenter's glue, 4 parts; Venice turpentine, 1.
  4. Eosin is melted, and into it is stirred calcined plaster till the mass is reduced to a paste, to which is added boiled oil, in sufficient quantity to bring it to the consistence of honey. It is applied warm.
  5. Into melted rosin, 180 parts, are stirred burnt umber, 30 parts; calcined plaster, 15 parts; boiled oil, 8 parts.
  6. Rosin, 4 to 5 parts; wax, 1 part; colcothar, 1 part; the whole melted together. A little powdered plaster is often added.
  7. Sandarac or galipot varnish, 15 parts; boiled linseed-oil, 5 parts; turpentine, 2½ parts; essence turpentine, 2½ parts; marine glue, 5 parts; pearl white, 5 parts; dry carbonate of lead, 5 parts; mixed.
  8. Copal or lac varnish, 15 parts; drying oil, 5 parts; indiarubber, or guttapercha, 4 parts; coal oil, 7 parts; Roman cement, 5 parts; plaster, 5 parts.
  9. Copal or rosin varnish, 15 parts; turpentine, 2½ parts; essence of turpentine, 2§ parts; fish isinglass, in powder, 2 parts; iron filings, 3 parts; ochre or rottenstone, 10 parts. These cements are much used for fixing metallic letters to glass, marble, or wood. The two following are particularly good for uniting brass and glass:
  10. Caustic soda, 1 part; rosin, 3 parts; plaster, 3 parts; water, 5 parts, the whole is boiled. This compound hardens at the end of half an hour; the hardening may be retarded by replacing the plaster by zinc white, white lead, or slaked lime.
  11. Fine litharge, 2 parts; white lead, 1 part; copal, 1 part; boiled linseed-oil, 3 parts; the whole is triturated together.
  12. For joining metallic surfaces, where soldering is inconvenient, recourse may be had to a composition formed in the following way: Pure and finely divided copper, such as that obtained by the reduction of sulphate of copper with zinc clippings, 20 to 36 parts, according to the degree of hardness desired in the cement, dissolved in a sufficient quantity of sulphuric acid to make a thick paste; with this is incorporated, by trituration in a mortar, mercury, 70 parts. The mass is soft, but hardens at the end of some hours. For use it is heated to 212° F. (100° C.), and powdered in an iron mortar heated to 302° F. (150° C.); it then assumes the consistence of wax, and is harder in proportion as it contains more copper. It adheres strongly on drying.
  13. To obtain a cement suitable for joining metals and non-metallic substances, mix liquid glue with a sufficient quantity of wood-ashes to form a thick mass. The ashes should be added in small quantities to the glue while boiling, and constantly stirred. A sort of mastic is thus obtained, which, applied hot to the two surfaces that are to be joined, makes them adhere firmly together. (14) A similar substance, may be prepared by dissolving in boiling water, 2½ lb. of glue and 2 oz. of gum ammoniacum, adding, in small quantities, about 2 oz. of sulphuric acid.


near cements, metal to glass, stone in Knolik


cements, meerschaumhome
letter "C"
start from "CE"
cements, microscopical

definition of word "cements, metal to glass, stone" was readed 694 times

Legal info